| - Battery Charging |
| |
|
|
Available in either a 5 watt or 10 watt panel kit. |
|
Solar Powered Battery Charger (GSP5), (GSP10)
The Solar Panel charges your gate opener's 12-volt battery when AC power is not available or is more than 1,000 feet away. Kit consists of a 5 or 10-watt solar panel, mounting pipe, mounting hardware and 8-feet of low voltage wire and installation instructions. [ more
info ]
Note: when using solar power to charge your gate opener battery, the number of cycles per day are limited by the number of solar panels installed and the geographic location of the gate opener installation. |
| |
|
|
|
|
| |
|
| |
|
|
 |
|
Replacement Battery (GRB1)
Standard 12-volt, 7.2 amp-hour battery for use with Zareba Automatic Gate Opener. The gate opener's control box has space built-in for an optional second battery.
|
| |
|
|
|
|
| |
|
| |
|
|
 |
|
1000 ft. Low Voltage Wire (GW1)
16-gauge, multi-stranded, dual-conductor low voltage wire used to connect the power source to the battery in the control box.
We recommend one continuous piece of wire be used, as a splice may corrode and inadequately convey power. Since every installation is unique, we do not include this wire in the Gate Opener kit. However, it is readily available by calling Zareba Systems or in the electrical department of most hardware stores. |
| |
|
|
|
|
| |
|
| - Anti-Theft |
| |
|
|
 |
|
Pin Lock (GPL1)
The pin lock gives your gate opener extra security with a keyed lock. The pin lock replaces the clevis pin when mounting the actuator to the brackets or to the gate, while still allowing quick release of the opener when you have the key.
|
| |
|
|
|
|
| |
|
| |
|
|
 |
|
Gate Lock (GL1)
The automatic gate lock provides an additional level of security for your property. When your gate swings shut, the gate lock closes, securing your gate in the closed position.
|
| |
|
|
|
|
| |
|
| - Access Control/Transmitter |
| |
|
|
 |
 |
 |
| One Button Transmitter (GT1) |
Two Button Transmitter (GT2) |
Three Button Transmitter (GT3) |
|
| |
| The one button transmitter is included with every Zareba Automatic Opener Kit. Additional transmitters are available. The two and three-button transmitters have additional programmable buttons that may be used with other devices such as an additional gate or garage door opener. All have a range up to 300-feet. |
| |
|
|
|
|
| |
|
| |
|
|
 |
|
Mini Transmitter (GKF1)
The Key Chain Transmitter fits on a keychain and allows you to open and close the gate from a remote location. Up to 300-foot range.
|
| |
|
|
|
|
| |
|
| |
|
|
 |
|
Push Button Control (GB1)
The Push Button control is similar to a doorbell, button-type control. Can open and close gate from a convenient, easily accessible location such as a garage or other location inside property.
|
| |
|
|
|
|
| |
|
|
|
|
|
|
 |
 |
|
Digital Keypad (GKP1)
The Keypad allows for entry by authorized guests informed of your pre-set code. Simple, wireless installation. Codes are easily changed.
|
|
| |
|
|
|
|
|
|
| |
|
| |
|
 |
 |
| |
|
Vehicle Sensor (GS1)
The In-Ground Vehicle Sensor automatically opens the gate without need for a transmitter, push button or keypad. Typically installed on the inside of the property, allowing guests to leave easily. Electro-magnetic sensor is buried near the gate and senses a vehicle when it passes by, sending a signal to the gate to open. 12-foot range. |
| |
|
|
|
| |
|
| |
|
|
 |
|
External Receiver (GDR1)
The Garage Door Receiver allows you to use your Zareba transmitter device to open your garage door and your gate. Eliminates the need for multiple control devices. Up to 300 feet range.
|
| |
|
|
|
|
| |
|
| - Hardware |
| |
|
| |
|
|
 |
|
Push to Open Bracket (GAB1)
This bracket is necessary for push-to-open installations, or where the gate opens out of the property. (Typically, gates open into the property, or pull-to-open mode.) The push-to-open installation may be necessary due to a sloped driveway or other owner-specific reason.
|
| |
|
|
|
|
| |
|
| |
|
